$$$$ @OTPOUT NOTICE CHAT 11/09/12 21:17:30 7124 DATE 11/09/12 Procedure @OTPOUT Voir aussi : ------------------ TAB1 DEP1 = @OTPOUT FLOT1 ENTI1 FLOT2 FLOT3 FLOT4 FLOT4 FLOT5 TAB2 TAB3 FORC1 RIG1 TAB4; Section : Mecanique Modele FRAN=========================================================== Objet : _______ Cette procedure,qui s'utilise en mode interactif, permet d'optimiser les hauteurs et les bases de modeles de poutres a section rectangulaire selon la methode du FULL-STRESS-DESIGN. Commentaires : ______________ TAB1 : objet de type TABLE; TAB1.I (type LISTREEL) pour la i-eme zone fournit une liste contenant les valeurs de base, hauteur et surface de la section, resultat de l'optimisation I (type ENTIER), DEP1 : champ de deplacement de la structure optimisee (type CHPOINT), FLOT1 : critere de convergence pour le sigma equivalent (type FLOTTANT), ENTI1 : nombre maximum d'iterations (type ENTIER), FLOT2 : base initiale des poutres de la structure, valeur identique pour toutes les zones (type FLOTTANT), FLOT3 : hauteur initiale des poutres de la structure, valeur identique pour toutes les zones (type FLOTTANT), FLOT4 : valeur optimale du sigma equivalent, calcule a partir des efforts flexionnels et membranaires normaux (type FLOTTANT), FLOT5 : plus petite dimension acceptable pour la poutre (type FLOTTANT), TAB2 : table contenant pour la i-eme zone l'objet relatif MMODL (type TABLE),TAB2.I (type MMODL), I (type ENTIER), TAB3 : table contenant pour la i-eme zone l'objet relatif avec les caracteristiques du materiau (type TABLE), TAB3.I (type MCHAML), I (type ENTIER), FORC1 : champ de forces (type CHPOINT), RIG1 : rigidite associee aux liaisons et a une partie de la structure n'ayant pas subi d'optimisation (type RIGIDITE), TAB4 : table contenant pour la i-eme zone le vecteur relatif pour l'orientation des axes locaux (type TABLE), TAB4.I (type POINT), I (type ENTIER), Note : ______ - La methode ne donnera un resultat optimal, d'un point de vue mathematique, que pour les structures isostatiques. - If faut diviser la structure en zones a l'interieur desquelles les dimensions des poutres sont supposees uniformes. - La convergence peut etre controllee par un parametre qui est appele interactivement a chaque iteration; il a pour fonction la reduction ou l'amplification de la variation des epaisseurs evaluee a chaque iteration sur la base du rapport entre le sigma equivalent maximum de la zone et le sigma equivalent optimal. ANGL=========================================================== Description : _____________ This procedure used in interactive mode enables the user to optimize both the heights and the bases of systems of beams with rectangular profile according to the FULL-STRESS-DESIGN method. Contents : __________ TAB1 : TABLE type object; TAB1.I (LISTREEL type) for the i-th region supplies a list containing the values of basis, height, and the surface of the profile stemming from the optimization I (ENTIER type), DEP1 : displacement field of the optimized structure (CHPOINT type), FLOT1 : convergence criterion for the equivalent sigma (FLOTTANT type), ENTI1 : maximum number of iterations (ENTIER type), FLOT2 : initial basis of the structure beams, same value for all the regions (FLOTTANT type), FLOT3 : initial height of the structure beams, same value for all the regions (FLOTTANT type), FLOT4 : optimum value of the equivalent sigma, calculated from normal flexural and membrane type efforts (FLOTTANT type), FLOT5 : minimum dimension permitted for the beams (FLOTTANT type), TAB2 : table containing for the i-th region the relative object MMODL (TABLE type),TAB2.I (MMODL type), I (ENTIER type), TAB3 : table containing for the i-th region the relative object with the material properties (TABLE type), TAB3.I (MCHAML type), I (ENTIER type), FORC1 : force field (CHPOINT type), RIG1 : stiffness associated with both the linkages and the part of the structure which is not subjected to an optimization (RIGIDITE type), TAB4 : table containing for the i-th region the relative vector for directing the local axes (TABLE type), TAB4.I (POINT type), I (ENTIER type), Note : ______ - Mathematically speaking, this method offers an optimum solution for isostatic structures. - The structure is divided in regions in which the dimensions of the beams are considered to be uniform. - The convergence can be controlled by a parameter which is called on, in interactive mode, at each iteration; it aims at reducing or amplifying the variation of the layers evaluated at each iteration on the basis of the ratio between the region maximum equivalent sigma and the optimum equivalent sigma. ITAL=========================================================== Oggetto: ________ Questa procedura, da usare interattivamente,permette di ottimizzare gli alteze e basi di sistemi di travi a sezione rettangolare secondo il metodo del FULL-STRESS-DESIGN. Commento : __________ TAB1 : oggetto di tipo TABLE; TAB1.I (type LISTREEL) per l'iesima zona fornisce una lista contenente i valori di base, altezza e area sezione risultato dell'ottimizzazione, I (type ENTIER), DEP1 : campo di spostamenti della struttura ottimizzata (type CHPOINT), FLOT1 : criterio di convergenza per la sigma equivalente (type FLOTTANT), ENTI1 : numero massimo di iterazioni (type ENTIER), FLOT2 : base iniziale delle travi della struttura, valore unico per tutte le zone (type FLOTTANT), FLOT3 : altezza iniziale delle travi della struttura, valore unico per tutte le zone (type FLOTTANT), FLOT4 : valore ottimale della sigma equivalente, calcolata a partire dai sforzi flessionali e membranali normali (type FLOTTANT), FLOT5 : dimensione minima accettabile per la trave (type FLOTTANT), TAB2 : tavola contenente per l'i-esima zona il relativo oggetto MMODL (type TABLE),TAB2.I (type MMODL), I (type ENTIER), TAB3 : tavola contenente per l'i-esima zona il relativo oggetto con le carratteristiche del materiale (type TABLE), TAB3.I (type MCHAML), I (type ENTIER), FORC1 : campo di forze (type CHPOINT), RIG1 : rigidezza associata ai vincoli e a parte di struttura non soggetta ad ottimizzazione (type RIGIDITE), TAB4 : tavola contenente per l'i-esima zona il relativo vettore per l'orientazione degli assi locali (type TABLE), TAB4.I (type POINT), I (type ENTIER), Note : ______ - Il metodo da' una soluzione ottima in senso matematico solo per strutture isostatiche. - La struttura va divisa in zone all'interno delle quali le dimensioni delle travi vengono assunte uniformi, - La convergenza puo' essere controllata con un parametro che viene richiesto interattivamente a ciascuna iterazione; la sua funzione e' di ridurre o amplificare la variazione degli spessori stimata ad ogni iterazione sulla base del rapporto tra sigma equivalente massima della zona e sigma equivalente ottimale.